Summa Creasing Tool D25 R0.75 W1.5 H1.5 for F Series Flatbed Cutters (500-9327)

F-series Modules & Tools

Each module can accommodate a variety of tools, blades and bits, allowing you to select the ideal tool for cutting your specific material and achieving the highest quality results. Every tool features a barcode ID for automatic recognition and parameter pre-sets. As your business expands, you can easily extend your tool range to meet new production demands.

AUTOMATIC DEPTH CONTROL:

The Automated Depth Control (ADC) simplifies tool, knife or bit changes significantly. The ADC measures the tip of the knife or bit accurately and sets the down position of the tool to the table’s level, thus guaranteeing a flawless cut.

Several creasing wheels, designed in different depths and radius sizes, are available for creasing and scoring paper, cartons, polypropylene and PVC material.

FEATURES:

• Clean creases without tearing
• Directional pressure adjustments

IDEAL FOR CREASING:

• Corrugated B-C-A-EE-BC flute (3 - 6mm)
• Corrugated C Flute (4mm)
• Corrugated E Flute (1.5mm)
• Paper < 200gr • Cardboard 300 - 500g/m²
• Polypropelene sheets <= 1.2mm
• Corrugated B-C-A-EE- BC flute (3-6mm)

The Double Edge Cutout Tool ensures minimal wear when cutting through rigid material up to 5mm thick. Here also, a spring-loaded gliding disk allows cutting of very precise details and can be fixed at a set depth.

FEATURES:

• Precise cutting of details
• Cuts at both knife sides
• Minimal knife wear
• Ideal to cut rigid material

IDEAL FOR CUTTING:

• Paper < 200g/m²
• Cardboard 300-500g/m²
• Adhesive vinyl
• Adhesive PVC
• PVC Banner
• Reflectivesheeting
• Expanded PVC board <= 1.2mm
• Polypropelene <= 1.2mm
• Polycarbonate <= 0.6mm
• Magnetic material

Ideal for cutting soft and medium density materials such as corrugated board and foam up to 18mm thick. The Electronic Oscillating Tool is driven by an electric motor, producing up to 12,000 rpm and moves a knife up and down over a stroke of 1mm.

FEATURES:

• Powerful cutting tool
• High processing speeds
• Low maintenance

IDEAL FOR CUTTING:

• Corrugated B-C-E Flute (1.5-4 mm)
• Foamcore with paper liner <= 10mm
• Foamcore with pa- per liner > 5mm
• Honeycomb board < 10mm
• Gasket

The Heavy-Duty Cutout Tool is suitable for cutting through thicker materials up to 15mm thick.

FEATURES:

• Ideal to cut very thick material

IDEAL FOR CUTTING:

• Cardboard 300-500g/m²
• Adhesive vinyl
• Adhesive PVC
• PVC Banner
• Corrugated PP board <= 5mm
• Expanded PVC board <= 1.2mm
• Polypropelene <= 1.0mm
• Polycarbonate <= 0.6mm
• Foamcore with paper liner <= 5mm
• Varnish blankets

With mechanically-controlled knife pressure, this tool is specifically designed for kiss-cutting material down to its liner up to 1.2mm thick. This tool also includes an adjustable nose piece for precise depth control.

FEATURES:

• Precise depth control
• Clean cuts for easy weeding
• Cuts a wide variety of vinyl and film

IDEAL FOR CUTTING:

• Paper < 200g/m²
• Adhesive vinyl
• Sandblast material
• Window film
• Magnetic material
• Adhesive PVC Banner material

The new Summa perforating tool for the F Series is used to make perforations in a very efficient and fast way. By using this tool, the perforated materials will be a lot easier to bend or fold. Then, the folds will have sharper 90° edges resulting in a nicer finish. This will save considerable time in the assembling of, for instance, cardboard or polypropylene boxes.

FEATURES:

• Up to 25 times faster cutting of perforation lines (versus EOT tool)
• Alternative for creasing. Folding and bending lines into cardboard
• High-quality perforated cuts
• Several knives available

IDEAL FOR CUTTING:

• Solid cardboard
• Corrugated board
• Polypropylene film

The standard Pneumatic Oscillating Tool, powered by compressed air, moves its knife up and down over a stroke of 8mm. The robust construction of the tool makes it suitable to cut thick material, such as honeycomb board, corrugated board and foam board.

FEATURES:

• High-performance cutting tool
• High processing speeds
• Availability of longer knife

IDEAL FOR CUTTING:

• Triple walled cardboard
• Double walled cardboard
• Packaging Foam
• Honeycomb board >= 10mm
• Foamcore with paper liner> 5mm
• Re-board®
• Foamboard with plastic
• Rubber

The Pneumatic Oscillating Tool-L (POT-L) is an addition to the standard POT and is used with a Longer type of knife. The POT-L is able to process thick, soft foams with a maximum thickness up to 42mm. The robust construction of the tool makes it suitable to cut thick material, such as honeycomb board, corrugated board and foam board.

FEATURES:

• High-performance cutting tool
• High processing speeds
• Availability of longer knife

IDEAL FOR CUTTING:

• Triple walled cardboard
• Double walled cardboard
• Packaging Foam
• Honeycomb board >= 10mm
• Foamcore with paper liner> 5mm
• Re-board®
• Foamboard with plastic
• Rubber

The Single Edge Cutout Tool is designed for detailed cutting through materials up to 6mm thick. A spring-loaded gliding disk allows cutting of very precise details and can be fixed at a set depth.

FEATURES:

• Precise cutting of details
• Cuts material up to 6mm thick
• Fixed depth setting

IDEAL FOR CUTTING:

• Paper < 200g/m²
• Cardboard 300-500g/m²
• Adhesive vinyl
• Foamboard <= 2mm
• Polypropelene <= 1.2mm
• Polycarbonate <= 0.6mm
• Adhesive PVC
• Magnetic material

The V-Cut Tools are available in 5 angles and are designed to cut a V-shaped groove in rigid sandwich and foam composite boards up to 27mm thick, depending on the material’s density.

FEATURES:

• Precise angle adjustment
• Very fast blade changes

IDEAL FOR CUTTING:

• Honeycomb board
• Foamcore with paper liner

Compatibility

Summa F1612, F1330, F1832, F3220 & F2630 Flatbed Cutters

Tech specs

• CREASING WHEEL DIAMETER: 25mm
• CREASING WHEEL RADIUS: 0.75mm
• CREASING WHEEL WIDTH: 1.5mm
• CREASING WHEEL HEIGHT: 1.5mm
• CONTROL: Electronic depth control via the Tangential Module
• COMPATIBILITY: Summa F1612, F1330, F1832, F3220 & F2630 Flatbed Cutters

This tool is designed to crease materials such as corrugated & non-corrugated cardboard, some corrugated plastics, foam boards & thin plastics. The creasing wheel fits into the Tangential Module of the Summa F Series Flatbed Cutters, allowing for precise electronic depth control during operation.

Similar products

Creasing Tool D25 R3 W8 H7 for F Series Flatbed Cutters (500-9325)

This tool is designed for creating creases in thicker or denser materials. The larger radius (R3) and the higher height (H7) enable it to efficiently process materials with more resistance to bending, such as corrugated board and heavy-duty packaging materials. This tool works well for creating deeper creases on materials that require precise, consistent folding and shaping.

Best suited for:

• Corrugated board
• Heavy-duty packaging materials
• Thick cardstocks

Creasing Tool D25 R1.5 W8 H5.5 for F Series Flatbed Cutters (500-9326)

This tool features a moderate radius (R1.5) with a medium height (H5.5). It is versatile and works effectively on a wide range of materials, including mid-weight cardstocks, light paperboard, and thinner packaging materials. The tool's moderate radius ensures a clean and consistent crease without causing material damage.

Best suited for:

• Paperboard
• Mid-weight cardstocks
• Thinner packaging materials

Creasing Tool D25 R0.75 W1.5 H1.5 for F Series Flatbed Cutters (500-9327)

This creasing tool has the smallest radius (R0.75) and the shortest height (H1.5), making it ideal for very precise, shallow creases. It works best with lightweight materials, including thin paper, fine cardstocks, and delicate packaging that requires minimal distortion or cracking at the crease. It’s perfect for products that demand intricate detail.

Best suited for:

• Lightweight paper
• Fine cardstocks
• Delicate packaging materials

Key Differences:

1. Radius (R): The first tool has the largest radius (R3), suitable for thicker materials, while the third has the smallest (R0.75), ideal for fine details.
2. Height (H): The height increases in the same order, with the first tool (H7) designed for heavier materials and the third tool (H1.5) being best for finer materials.
3. Material Suitability:
   • The first tool is best for thicker and sturdier materials.
   • The second tool is versatile, suited for mid-weight materials.
   • The third tool is suited for delicate, lighter materials.