Neschen UV Dot Print'n'Walk Floor Graphics Film 200µm 6037897 54" 1372mm x 30m roll

Other available sizes

Neschen | UV Dot Print'n'Walk Floor Graphics Film 200µm | 6037895 | 42" 1067mm x 30m roll

Neschen | UV Dot Print'n'Walk Floor Graphics Film 200µm | 6037897 | 54" 1372mm x 30m roll

Neschen | UV Dot Print'n'Walk Floor Graphics Film 200µm | 6036727 | 61" 1550mm x 30m roll

Neschen | UV Dot Print'n'Walk Floor Graphics Film 200µm | 6042660 | 63" 1600mm x 30m roll

Application instructions

Neschen UV Dot Print'n'Walk Floor Graphics Film can only be used on floors with temperatures of between 15 and 40°C. If floor heating is in place, it should be ensured that the heating medium does not exceed the stated temperature range. Generally speaking, this should not be the case with floor heating systems that are operated in the usual manner.

Neschen UV Dot Print'n'Walk Floor Graphics Film should be glued down during periods when the material will be subjected to either no mechanical loads or as few as possible. As a result, it is recommended that application take place shortly before close of business, for example, and that the laminate be left to rest overnight. We recommend a “rest period” of at least 12 hours before carrying out the first mechanical cleaning procedure. However, it is possible to walk on the floor immediately. As is normal for floor coverings, the UV dot print’n’walk becomes slippery when wet. To guarantee maximum safety, the UV dot print’n’walk should not be applied to areas which may become wet as a result of exposure to rain or snow. You are strongly advised to use doormats in entrance areas.

Before gluing the UV dot print’n’walk onto floor coverings, please ensure that these are in perfect condition. Particularly in cases where the floor covering is not adequately fixed to the subsurface, the floor covering may be lifted off when the UV dot print’n’walk is removed. Loose tiles (or similar) must be repaired before the UV dot print’n’walk can be glued in place. The subsurface onto which the Floor Graphics Solution is to be applied should be as smooth as possible. Prior to gluing, thorough cleaning (as outlined above) must be performed as a matter of course. Applying the material to carpeted floors is not recommended.

• Gradually remove the release liner, applying the adhesive as it becomes exposed.
• Position the UV dot print’n’walk on the floor, which has been prepared as described above
• Avoid gluing the border areas over indentations or uneven parts such as gaps (or similar). If the laminate is being bonded onto tiles with deep gaps, apply a squeegee to each tile, working from the center outwards until you reach the gaps.
• Use a squeegee or hand roller to press the laminate firmly onto the subsurface, working from the center outwards. While doing this you should ensure that the entire graphic is glued down, and that no air bubbles are present. However the biggest advantage of UV dot print’n’walk is that it enables work bubble free even when applied by nonprofessional person.
• Ensure that direct contact cannot be made with the glued surface; or, if this is unavoidable, that contact is only made with lint-free gloves or hands that are clean, dry and grease-free.
• Avoid contact with the corners and edges, as these are the most important points for ensuring adhesion to the subsurface.
• Where possible, use a motif with rounded contours, since sharp corners and edges constitute weak points where removal may occur.
• It's recommended the image be applied in a single piece. Overlapping is not recommended.
• If removal at the corners occurs as a result of heavy mechanical strain, these corners should be rounded wherever possible. Once the subsurface has been cleaned, the laminate should be reapplied with increased pressure.
• It is not necessary to seal the UV dot print’n’walk with floor wax or adhesive tape for the edges, but increases its service life

Care & Maintenance

Neschen UV Dot Print'n'Walk Floor Graphics Film is a high-quality product that has been developed over decades of experience in the field of floor coverings. As a result, it boasts outstanding properties in terms of its resistance to scratches, non-slip surface and reaction to soiling. Despite this, it is, of course, impossible to prevent soiling from occurring. Where wet surfaces are concerned, there is naturally a markedly increased risk of slippages occurring, although the system's properties in this respect fulfil extremely stringent requirements.

It is possible to perform cleaning from time to time using mild soap-based products diluted in water. After cleaning, ensure that the surface is completely dry before allowing it to be walked on again. Prevent the border areas from coming into contact with water for extended periods, since the adhesive used is an environmentally-friendly, water-based material whose adhesive properties may be diminished as a result.

Heavy, sharp-edged items that either move across the surface or are placed on top of it may lead to damage occurring. For this reason, avoid applying the UV dot print’n’walk in areas whose floors are exposed to heavy loads. The best locations for applying the UV dot print’n’walk are those which have normal levels of foot traffic.

Surface treatment

To ensure safety and prevent the subsurface from being damaged on removal, the UV dot print’n’walk has to be bonded on the entire surface. The floor covering must be in good condition and firmly fixed in place. Prior to gluing, we suggest carrying out the following steps:

• Ensure that the floor covering is firmly affixed to the subsurface. If this is not the case, the covering may lift off during removal.
• Repair any tiles that are, for example, loose-fitting or uneven.
• Clean the subsurface in accordance with the instructions below.

It is recommended to perform the following cleaning procedures:

• If there is evidence of any oily contaminants (or similar) on the surface, apply alcohol or a gentle solvent of a similar nature to it as a pre-cleaning procedure. Ensure that such contaminants have been completely removed before continuing with any other cleaning procedures.
• Following this, use a mild surfactant-based detergent. This should be free from enzymes. Ensure that the entire surface is cleaned, and that the detergent is removed without leaving any residue.
• The size of the cleaned surface should exceed that of the adhesive surface by at least 20 cm in all directions.
• Make sure that the floor is dry and clean. For drying purposes, only lint-free cloths should be used.

* If this cleaning agent is used, the instructions for use provided by the manufacturer must be followed as closely as possible. Prior to use, the user of these chemicals must be aware of information on the labels, as well as the safety data sheets.

Related Products

Neschen | UV Dot Print'n'Walk Transparent Floor Graphics Film 200µm | 6040068 | 61" 1550mm x 30m roll

Neschen | UV Dot Print'n'Walk Transparent Floor Graphics Film 200µm | 6042661 | 63" 1600mm x 30m roll