Canon IJM424 Repositionable Self-adhesive Textile 286g/m² 97004169 36" 914mm x 30m roll **CRYSTAL POINT / WATER-BASED / LATEX INKS**

Core Size
3 inch

Width / Size
914mm / A0+ / 36"

Download
Brochure

Canon IJM424 Repositionable Self-adhesive Textile 286g/m² 97004169 36" 914mm x 30m roll CRYSTAL POINT / WATER-BASED / LATEX INKS

£335.99 inc VAT

£279.99 ex VAT

Would you like to talk to a specialist about this product?

01905 454598 [email protected]

All you need to know about the Canon IJM424 Repositionable Self-adhesive Textile 286g/m² 97004169 36″ 914mm x 30m roll **CRYSTAL POINT / WATER-BASED / LATEX INKS**

Description Other available sizes Surface Preparation Installation Techniques Finishing Removal

Canon IJM424 Repositionable Self-adhesive Textile 286g/m²: Thinly woven self-adhesive polyester fabric with a paper backing and repositionable adhesive allowing the product to be repositioned or reapplied on smooth and flat surfaces.

IJM424 has a low tack, pressure sensitive adhesive that allows the product to be repositioned and reapplied. This makes it ideal for wall coverings, board displays, window decorations, back-lit and acrylic board display etc.

IJM424 is designed for painted sealed walls (no Eco paint) and smooth, flat surfaces such as: Stainless steel, aluminium, glass, styrene, polycarbonate, Acrylic board, Plexiglas®, Sintra®, Gatorfoam® and Fome-Core®. Do not apply IJM424 to uneven or curved surfaces, such as 90° bends. Textured surfaces, like perforated / tough painted wall and wooden surfaces tend to promote poor adhesion. Always pre-test your specific substrate for compatibility and removability prior to actual application.

APPLICATIONS:

Wall covering, Wall graphics
Window decoration, POP
Signage, Backlit, Label
Photo sticker

FEATURES:

Excellent print quality
Easy to apply, easy to remove
Repositionable
Matt surface
3" core + 2" adapter

Canon | IJM424 | Repositionable Self-adhesive Textile 286g/m² | 97004169 | 36" 914mm x 30m roll

Canon | IJM424 | Repositionable Self-adhesive Textile 286g/m² | 97004170 | 42" 1067mm x 30m roll

Always ensure that the receiving substrate is thoroughly cleaned, free of dust, dirt or cleaner residues. Painted surfaces should be painted with latex paint containing no waxes or silicones. Metal and glass surfaces can be cleaned with standard glass cleaners.

Poor surface conditions will cause adhesion loss or failure. Minimum surface temperature is 10°C. Life expectancies can vary depending on mounting surface and environment conditions.

Proper contact of the adhesive to mounting substrate is crucial and maximum pressure should be applied during installation. If insufficient pressure is used during the install, the edges can lift. It is recommended to use a cold roll laminator to apply adequate even pressure during application.

For installations by hand the use of a soft roller is advised. Make sure that enough even pressure is applied. Using a low tack application tape and a squeegee with sufficient pressure is also an option. Always pre-test the application tape to make sure that it can be used without damaging the print. Do not apply with water because the adhesion will be negatively affected.

A liquid laminate may be used. Let image dry for 24 hours before applying a finish. Always pre-test liquid laminates for compatibility. Do not use liquid laminates on ColorWave CrystalPoint prints.

When removing IJM424 from any surface, remove slowly and lift at a 90° angle. Different surfaces will have different adhesion characteristics.

Glass, stainless steel, and aluminum surfaces usually promote higher adhesive bonds, are more difficult to remove and may leave adhesive residue during removal. If during the removal adhesive transfer happens, soapy warm water and aggressive rubbing with a cloth should remove adhesive. Also longer application time can promote adhesive transfer.

DATA SHEET